If your basketball net has frayed down to a few loose strands or rotted off the rim, all you need is a new net and a sturdy ladder to upgrade it and get back to the game.
How to put a net on a basketball hoop comes down to one move repeated 12 times: hook each loop of your net onto the rim, then pull it tight. The attachment technique changes slightly if your basketball hoop rim uses enclosed fittings instead of exposed hooks, so check it before you start.
What You’ll Need Before Installing the Net
Gather the right tools before you climb. This includes:
- A basketball net replacement that fits your rim
- A sturdy ladder that doesn’t wobble
- Tape for marking spots on the rim
- Scissors if the old net needs to be cut away
- Work gloves if the metal attachment points feel rough
- Pliers if your chain net uses clips that must be closed
Set the ladder on firm, level ground and keep three points of contact as you climb, as Consumer Reports recommends. Ask a helper to hold it steady while you work. If you have an adjustable basketball hoop, lowering it before you work may make the job easier. Reset it afterward using the correct measurement for the player, as covered in our basketball hoop height guide.
How to Put a Net on a Basketball Hoop With Hooks
The standard hook-and-loop method is a good way to install a conventional net securely. If you’re putting one up for the first time, work around the rim in the following order, so you don’t have to fix the spacing afterward:
Step 1: Remove the Old Basketball Net
Pull each old loop free from its hook or attachment slot. If weather has made the cord brittle, cut that section with scissors instead of pulling hard on the rim. Wear gloves and watch for rust on the hook and other metal parts as you clear debris off the rim. Once the net is down, run a visual check around the rim and remove loose debris before you continue.
Step 2: Find all the Attachment Points
A standard basketball net has 12 top loops, and a standard rim has 12 attachment points to match. On many home hoops, those attachment points look like open metal hooks. Other rims use a slotted or enclosed tube, so the connection shape can vary even though the loop count is the same.
Step 3: Check the Net Orientation
Find the wider end of the basketball net before attaching anything. The larger loops belong against the rim, while the net should narrow as it hangs toward the basket opening below.
Step 4: Attach one Loop at a Time
Take one top loop and feed it over or through the first hook so it sits flat. Continue around the rim until every loop has its own attachment point. Keep counting and do not double two loops onto one hook because it will lead to uneven spacing around the rim.

Step 5: Do a Final Check
Once every loop is attached, pull down gently around the bottom of the net. It should hang straight, with no section tighter than another. Then shoot a few basketballs through the hoop to confirm it slows the ball briefly before a clean release.
If the rim wobbles when you shake it, the net isn’t the problem. See how we install a PROformance hoop for a solid setup.
How Do You Put a Net on a Hoop Without Hooks?
For a rim with eyelets or enclosed attachment channels, thread each top loop through its matching opening and pull it snug so it can’t slip back out. If the hoop uses separate clips, use the correct clips instead of forcing the net into an opening that was not designed to hold it.
In some situations, zip ties are used as a temporary attachment when a recreational rim has no usable hooks. If you go that route, trim the ends flush and check that no sharp plastic edge can reach a player's hands.
You may also see DIY advice suggesting strapping tape, duct tape wrapped around net loops, picture-frame wire, or thin metal wire threaded through a hollow rim tube. We wouldn’t use those as a permanent fix on a playing hoop because exposed wire can create sharp contact points, and tape can loosen outdoors during intense games.
How to Tie a Basketball Net With String
Cord works when a rim has no hooks, or when a hook snaps off, and you have no spare. Follow these steps:
- Mark 12 evenly spaced spots around the rim with tape so the net hangs level.
- Cut a length of cord for each loop, long enough to wrap the rim and tie off.
- Run a cord through a net loop and around the rim at a marked spot, then tie a double knot.
- Repeat at every spot and trim the loose ends. Then check that each loop hangs the same distance from the rim.
If your rim came with the manufacturer’s instructions, follow them over any general guide.
How Do You Install a Chain Basketball Net?
A chain net uses S-hooks or purpose-made clips that connect the chain to the rim's existing attachment points. Follow this order to install one:
- Lay the chain out first so you can spot a twist before installation.
- Wear gloves, because the links and hooks can be sharp.
- Attach the supplied clip or S-hook at each rim connection, then connect the corresponding top section of chain and continue around the hoop.
- Close any open hook with the pliers so it can’t pop off.
- When the chain is fully attached, check that each section hangs to roughly the same level and that no open clip can snag a hand or the ball.
Which Type of Basketball Net Should You Buy?
The best net depends mostly on where the hoop sits and how much weather it sees. Here are the three options:
|
Net type |
Suitability |
What to know |
|
Nylon basketball net |
Home driveways and indoor courts |
Nylon is familiar and quieter than metal, which suits occasional play. |
|
Heavy-duty braided nylon net |
Outdoor home hoops and school playgrounds |
Weather-resistant fibers make sense when the net will spend a lot of time in changing Ohio weather. |
|
Chain basketball net |
Public courts with heavy use |
Chain has an iconic clinking sound and retains its rigid shape. |
For most homeowners, a nylon basketball net is the straightforward choice because replacing it does not require special tools on a compatible rim. It also gives a soft swish and slows the ball as it drops through the basket. Our replacement netting is heavy-duty braided nylon with a standard 12-loop design, so it fits standard 12-loop rims and works on indoor and outdoor hoops.

Get Your Hoop Ready for the Next Game
Once you learn the technique, a net swap takes little time and gives an old hoop a clean look. If your hoop needs more than a new net, our backyard basketball court setup guide covers the full layout.
Visit our Powell or Milford showroom to explore our basketball hoops in person and talk with our team about what would work best for your driveway. We'll help you compare backboard sizes and adjustable-height options based on your space and the players at home.

